Chevrolet Captiva Manuals

Chevrolet Captiva Service & Repair Manual: Brake Pads R&R

Warning: Avoid taking the following actions when you service wheel brake parts: Do not grind brake linings, do not sand brake linings and do not clean wheel brake parts with a dry brush or with compressed air.
Warning: Some models or aftermarket brake parts may contain asbestos fibers which can become airborne in dust. Breathing dust with asbestos fibers may cause serious bodily harm. Use a water-dampened cloth in order to remove any dust on brake parts. Equipment is available commercially in order to perform this washing function. These wet methods prevent fibers from becoming airborne.

Front

Removal

Caution: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.
Always replace disc brake pads in axle sets.
DO NOT use any air tools to remove or install the guide pin bolts. Use hand tools ONLY.
Install an open end wrench to hold the caliper guide pin in line with the brake caliper while removing or installing the caliper guide pin bolt. DO NOT allow the open end wrench to come in contact with the brake caliper. Allowing the open end wrench to come in contact with the brake caliper will cause a pulsation when the brakes are applied.
1. Inspect the fluid level in the brake master cylinder reservoir.
2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid needs to be removed before proceeding.
3. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove brake fluid to the midway point before proceeding.
4. Raise and support the vehicle.
5. Remove the tire and wheel assembly.
6. Remove the lower brake caliper guide pin bolt (1). Hold the brake caliper guide pin stationary when removing the guide pin bolt, Fig. 1.
7. Pivot the brake caliper (1) upward and support with heavy mechanics wire or equivalent, Fig. 2.
8. Place a block of wood or an old brake pad against the brake caliper pistons.
9. Using a brake pad spreader tool or equivalent, fully seat the caliper pistons in the caliper bores.
10. Remove the inner brake pad (1) and the outer brake pad (2). Note the location of the brake pad wear sensor for correct installation, Fig. 3.
11. Remove the upper and lower brake pad shims (1), Fig. 4.
12. If installing new brake pads, discard the shims.

Installation

DO NOT use any air tools to remove or install the guide pin bolts. Use hand tools ONLY.
Install an open end wrench to hold the caliper guide pin in line with the brake caliper while removing or installing the caliper guide pin bolt. DO NOT allow the open end wrench to come in contact with the brake caliper. Allowing the open end wrench to come in contact with the brake caliper will cause a pulsation when the brakes are applied.
1. Install the upper and lower brake pad shims. If installing new brake pads, install new shims.
2. Install the inner brake pad and the outer brake pad. Note the location of the brake pad wear sensor for correct installation.
3. Pivot the brake caliper into position and install the lower brake caliper guide pin bolt. Hold the brake caliper guide pin stationary when installing the guide pin bolt. Torque the bolt to 20 ft. lbs.
4. Install the tire and wheel assembly.
5. Lower the vehicle.
6. With the engine OFF, gradually apply the brake pedal to approximately 2/3 of its travel distance.
7. Slowly release the brake pedal.
8. Wait 15 seconds, then repeat steps 6-7 until a firm brake pedal is obtained. This will properly seat the brake caliper pistons and brake pads.
9. Fill the master cylinder reservoir to the proper level.
10. Burnish the pads and rotors.

Rear

Removal

Caution: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.
Always replace disc brake pads in axle sets.
DO NOT use any air tools to remove or install the guide pin bolts. Use hand tools ONLY.
Install an open end wrench to hold the caliper guide pin in line with the brake caliper while removing or installing the caliper guide pin bolt. DO NOT allow the open end wrench to come in contact with the brake caliper. Allowing the open end wrench to come in contact with the brake caliper will cause a pulsation when the brakes are applied.
1. Inspect the fluid level in the brake master cylinder reservoir.
2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid needs to be removed before proceeding.
3. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove brake fluid to the midway point before proceeding.
4. Raise and support the vehicle.
5. Remove the tire and wheel assembly.
6. Remove the lower brake caliper guide pin bolt (1). Hold the brake caliper guide pin stationary when removing the guide pin bolt, Fig. 5.
7. Pivot the brake caliper (1) upward and support with heavy mechanics wire or equivalent, Fig. 6.
8. Place a block of wood or an old brake pad against the brake caliper pistons.
9. Using a brake pad spreader tool or equivalent, fully seat the caliper piston in the caliper bore.
10. Remove the outer brake pad (1) and the inner brake pad (2). Note the location of the brake pad wear sensor for correct installation, Fig. 7.
11. Remove the upper and lower brake pad shims (1), Fig. 8.
12. If installing new brake pads, discard the shims.

Installation

DO NOT use any air tools to remove or install the guide pin bolts. Use hand tools ONLY.
Install an open end wrench to hold the caliper guide pin in line with the brake caliper while removing or installing the caliper guide pin bolt. DO NOT allow the open end wrench to come in contact with the brake caliper. Allowing the open end wrench to come in contact with the brake caliper will cause a pulsation when the brakes are applied.
1. Install the upper and lower brake pad shims. If installing new brake pads, install new shims.
2. Install the outer brake pad and the inner brake pad. Note the location of the brake pad wear sensor for correct installation.
3. Pivot the brake caliper into position and install the lower brake caliper guide pin bolt. Hold the brake caliper guide pin stationary when installing the guide pin bolt. Torque the bolt to 20 ft. lbs.
4. Install the tire and wheel assembly.
5. Lower the vehicle.
6. With the engine OFF, gradually apply the brake pedal to approximately 2/3 of its travel distance.
7. Slowly release the brake pedal.
8. Wait 15 seconds, then repeat steps 6-7 until a firm brake pedal is obtained. This will properly seat the brake caliper pistons and brake pads.
9. Fill the master cylinder reservoir to the proper level.
10. Burnish the pads and rotors.

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Fig. 8

    Brake Master Cylinder Reservoir R&R
    Removal 1. Using a suitable tool, remove the brake fluid from the brake master cylinder reservoir. 2. Discard the brake fluid into an ap ...

    Brake Power Booster Unit Check Valve R&R
    2.4L A small amount of denatured alcohol may be used to ease assembly. Do not use soap. 1. With the engine OFF, apply and release the brake pedal se ...

    More about:

    Chevrolet Captiva Owners Manual > OnStar: OnStar Overview
    If equipped, this vehicle has a comprehensive, in-vehicle system that can connect to a live Advisor for Emergency, Security, Navigation, Connection, and Diagnostic Services. The OnStar system status light is next to the OnStar buttons. If the status light is: Solid Green: System is rea ...

    Chevrolet Captiva Owners Manual

    Chevrolet Captiva Service & Repair Manual

    © 2024 Copyright www.ccaptiva.com - 0.0071