Chevrolet Captiva Manuals

Chevrolet Captiva Service & Repair Manual: Parking Brake Cable Adjust

Chevrolet Captiva Service & Repair Manual / Brakes / Parking Brake Cable Adjust

Procedure

If the rear wheels rotate during the following test, repeat the adjustment procedure completely.
1. Disable the parking brake cable adjuster.
2. Turn the ignition to the OFF position.
3. Raise and support the vehicle.
4. Remove the rear tire and wheel assemblies.
5. Remove the rear brake rotors.
6. Set the CH-21177-A drum to brake shoe clearance gauge inside of the drum portion of the disc brake rotor at the widest point. Place the contacts on the tool to the widest point of the park brake drum (1). Tighten the set screw on the tool prior to removing the tool from the drum, Fig. 1.
7. Position the CH-21177-A drum to brake shoe clearance gauge over the parking brake shoes (1) at the widest point, Fig. 2.
8. Turn the adjuster on the actuator until the park brake shoes just contact the CH-21177-A drum to brake shoe clearance gauge.
9. Repeat steps 6-8 for the opposite parking brake assembly.
10. Install the rear brake rotors.
11. Install the rear tire and wheel assemblies.
12. Enable the parking brake cable adjuster.
13. Apply the electronic parking brake.
14. Place the transmission in NEUTRAL.
15. Raise and support the vehicle so the tire and wheel assemblies are clear of the ground.
16. Attempt to rotate the rear tire and wheel assemblies. The wheels should not rotate forward. The wheels should not rotate rearward, or should exhibit significant rearward drag.
17. Release the electronic parking brake.
18. Verify the rear tire and wheel assemblies rotate freely and do not exhibit forward or rearward drag.
19. If the rear tire and wheel assemblies do not rotate freely and without forward or rearward drag, repeat the adjustment procedure completely.

Adjuster Disabling

The park brake cable tension is controlled by the electronic park brake (EPB) module. Tension can be fully released from the park brake cables to allow for service of the park brake system. Perform one of the following methods to fully release cable tension.

Electronic Method

With Scan Tool -- Preferred
1. Block the drive wheels.
2. Install a scan tool to the vehicle.
3. Turn the ignition switch to the ON/RUN position with the engine OFF.
4. Using the scan tool, perform the following:
  a. From the scan tool menu, select "Diagnostics."
  b. Enter the appropriate vehicle information.
  c. Select "Chassis."
  d. Select "Parking Brake Control Module."
  e. Select "Special Functions."
  f. Select "Cable Replacement."
5. Follow the instructions on the scan tool to fully release the tension on the parking brake cables.
Less Scan Tool -- Optional
1. Block the drive wheels.
2. Turn the ignition switch to the ON/RUN position with the engine OFF.
3. Place the automatic transmission in PARK or manual transmission in NEUTRAL, as equipped.
4. Apply and hold the brake pedal. The brake pedal must remain applied throughout the park brake cable tension release process.
5. Press and hold down the electronic park brake (EPB) switch approximately five seconds.
6. Observe the PARK BRAKE lamp on the instrument cluster.
7. When the PARK BRAKE lamp flashes, release then immediately press and release the EPB switch. The parking brake cable tension is fully released.
8. Release the brake pedal.

Manual Method

In the event the above methods to release the parking brake cable tension are unsuccessful, the following procedure may be necessary to release the parking brake cable tension.
The protective plug for the manual release is located near the electrical connector.
Do NOT use power tools to rotate the manual release mechanism. Use of power tools can damage the EPB module gear drive mechanism.
1. Raise and support the vehicle.
2. Remove the protective plug from the EPB manual release.
3. Using an appropriate tool, rotate the mechanism clockwise until the tension is fully released from the parking brake cables. Up to 50 cycles may be required until the parking brake cable tension is fully released.
4. Install the protective plug to the EPB module.

Adjuster Enabling

The park brake cable tension is controlled by the electronic park brake (EPB) module. Cable tension needs to be set and the EPB module needs to be calibrated following the cable tension disabling procedure. Perform one of the following two methods to fully restore cable tension.

Electronic Method

With Scan Tool -- Preferred
1. Block the drive wheels.
2. Install a scan tool to the vehicle.
3. Turn the ignition switch to the ON/RUN position with the engine OFF.
4. Using the scan tool, perform the following:
  a. From the scan tool menu, select "Diagnostics."
  b. Enter the appropriate vehicle information.
  c. Select "Chassis."
  d. Select "Parking Brake Control Module."
  e. Select "Module Setup."
  f. Select "Parking Brake Calibration."
5. The EPB module will be calibrated and proper tension will be applied to the parking brake cables.
Less Scan Tool -- Optional
1. Block the drive wheels.
2. Turn the ignition switch to the ON/RUN position with the engine OFF.
3. Apply the brake pedal.
4. Place the automatic transmission in PARK or manual transmission in NEUTRAL, as equipped.
5. Momentarily lift then release the EPB switch to apply the EPB.
6. Momentarily press down then release the EPB switch to release the EPB.
7. Repeat steps 5-6 to cycle the EPB on then off an additional four times.
8. The EPB module will be calibrated and proper tension will be applied to the parking brake cables.

Fig. 1

Fig. 2

    Parking Brake Activation Switch R&R
    1. Remove the front floor console accessory trim plate upper, Fig. 1. 2. Remove parking brake actuator switch bolts, Fig. 1. ...

    Parking Brake Cable R&R
    Front Removal 1. Disable the parking brake cable adjuster. 2. Turn the ignition to the OFF position. 3. Raise an ...

    More about:

    Chevrolet Captiva Owners Manual > Controls: Windshield Wiper/Washer
    The windshield wiper lever is on the right side of the steering column. Move the lever up or down to select the wiper speed. (Mist): Single wipe, briefly move the lever down. The lever returns to its starting position when released. For several wipes, hold the lever down. (Off): ...

    Chevrolet Captiva Owners Manual

    Chevrolet Captiva Service & Repair Manual

    © 2024 Copyright www.ccaptiva.com - 0.0069